QSC Audio RMX 5050 | 2 Channel, 1100W per Channel @ 8 Ohm,

QSC Audio RMX 5050

The QSC RMX Series amplifiers provide studio quality sound in a 2 rack space. These amps give you clean dynamic power with the same reliability for which QSC is known. You know you are getting a quality product when QSC backs it up with a free 6 year warranty! The RMX Series amplifiers are built to last and are very dependable.

Features:

The new flagship of the RMX line, the RMX 5050 provides extremely high power and represents tremendous value
The RMX 5050 provides advanced thermal performance, delivering higher continuous power in 2-ohms stereo or 4-ohms bridged applications
Dual mono, high current power supply for increased reliability and performance
3RU chassis only 16" deep
Professional quality performance - incorporates road-proven QSC designs
High-current toroidal transformers for greater two-ohm power and low noise
Independent user-defeatable clip limiters reduce distortion
Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom
Balanced 1/4" (6.3 mm) TRS, XLR, and barrier strip inputs for maximum flexibility
Binding post and Neutrik Speakon outputs
Front mounted gain controls for easy access
Signal and Clip LED indicators to monitor performance
3-year warranty. An optional 3-year extended service contract is available. Ask your dealer for details.

SPECIFICATIONS	RMX 5050
	STEREO MODE, Both Channels Driven
8 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD	1050 W 1100 W
4 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD	1600 W 1800 W
2 ohms FTC 20 Hz-20 kHz 0.1% THD EIA 1 kHz 1% THD	2000 W 2500 W
	BRIDGE-MONO MODE
8 ohms FTC 20 Hz-20 kHz 0.1% THD EIA 1 kHz 0.1% THD	3200 W 3600 W
4 ohms EIA 1 kHz 1% THD	5000 W
Distortion (SMPTE-IM)	Less than 0.02%
Distortion (Typical) 20 Hz - 20 kHz: 10 dB below rated power 1 kHz and below: full rated power	Less than 0.02% Less than 0.02%
Frequency Response	20 Hz - 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB 5 Hz - 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB
Damping Factor	Greater than 250 @ 8 ohm
Noise (unweighted)	100 dB below rated output (20 Hz - 20 kHz, 8 ohm load)
Input Sensitivity	1.42 Vrms for 1050 watts into 8 ohms
Voltage Gain	64x (36 dB) for 8 ohm load
Input Impedance	20k ohm balanced, 10k ohm unbalanced
Controls Front: Controls Rear:	AC power switch, Ch. 1 and Ch. 2 gain control 10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.
Indicators	Power-On: Green LED, Protect: Red LED Signal -30dB: Yellow LED, Clip: Red LED
Connectors Input: Connectors Output:	XLR female, TRS (1/4"), and barrier-strip screw terminals, each channel Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp)
Cooling	Continuously variable-speed fan, rear-to-front air flow
Amplifier Protection	Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads
Load Protection	On/off muting, DC fault output crowbar
Power Requirements	100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured) 120V models require 20 Amp service and are supplied with a NEMA 5-20 plug on the cordset.
Dimensions	19" (48.3 cm) wide, 5.25" (13.3 cm) tall, 15.9" (40.39 cm) overall depth
Weight	75 lbs (34.02 kg) net, 87 lbs (39.46 kg) shipping